Leaky Homes & Weathertightness
-
Leaky Homes are a growing concern as more examples become exposed every day.
-
The best time to deal with weathertightness is at the design stage where different options can be considered and changes are easily made to the plans. It is important for the designer, builder and owner to look at the risks associated with the proposed building and reduce these to acceptable levels before building.
-
Sometimes materials are used in ways for which they are not specifically designed or are poorly maintained, leading to cracking and leaking. Make sure you are aware of the maintenance requirements of all specified materials for your home –incorrect or lack of maintenance will often mean your product’s warranty becomes void.
-
Modern designs can also have insufficient level difference between the floor of a building and the surface outside. An adequate level difference is necessary if the building is to meet the performance requirements of the Building Code in regard to external moisture provisions.
• Information supplied courtesy of BRANZ
FOR MORE INFORMATION ON WEATHERTIGHTNESS INITIATIVES VISIT WWW.WEATHERTIGHT.ORG.NZ OR, IF YOU THINK YOU MIGHT HAVE A PROBLEM WITH YOUR HOME THAT IS LEAKING, THEN CONTACT WWW.HOBANZ.ORG.NZ FOR ADVICE.
YOU MUST BEGIN YOUR CLAIM WITHIN TEN (10) YEARS OF CONSTRUCTION. IF YOU THINK YOUR HOME MIGHT BE LEAKING THEN ACT SOONER RATHER THAN LATER.
Common Design Issues Leading to Leaking
Decks enclosed by solid walls. These walls usually have a textured finish and a flat top surface (also textured) with a handrail fixed to it. Water cannot drain from the surface and the weather-proofing skin has been penetrated by the fixings or the rail support, making these walls almost impossible to waterproof. It may then take only six months for serious deterioration of wall framing to occur.
Wall-cladding materials finished hard down onto a deck surface or paving or paths. By doing this the cladding will absorb water from the surface it is finished onto. Any water that might pass through the cladding is also prevented from draining out at the bottom. It’s even worse if wall cladding materials are taken below the ground level or if landscaping materials, such as mulch, are built up against the wall. Materials that are continuously damp will deteriorate faster.
Waterproof decks constructed with the deck surface close to the same height as the building floor with no provision for the water that will fall onto the surface. Often there is no fall to drain the water away from the building and no overflows. When the outlet blocks, the only place for the water to go is inside the building.
Buildings with suspended timber floors require the space below the floor to be ventilated to remove moisture that evaporates from the ground. It is common, particularly in renovation projects, to see vents blocked by decks, paving, planters or soil. Restricting the ventilation rate significantly increases the risk of dampness and mould within the buildings and also the potential for damp-related deterioration.
Image courtesy BRANZ
Other Design/Detailing Concerns
- Using sealant instead of properly designed flashings
- Designing parapet walls without a cap flashing or slope to drain water from them
- Not installing head and sill flashings to windows
- Not installing kick-outs or diverters to apron flashings where roofs abut wall surfaces – kick-outs are necessary to ensure that water flows into the gutter and not down inside the walls
- Using design features that penetrate the cladding, such as projecting timber beams or handrails. It is almost impossible to effectively and durably waterproof these penetrations
- Not allowing for movement in monolithic claddings and tiled finishes – these finishes require movement control joints to allow building movement to occur without cracking
- Following building trends that ignore features known to provide some weather protection, such as eaves and drip edges to the base of claddings and above windows, though be aware that even houses with eaves have been known to leak.
- Poor or no detailing of junctions between materials
Leaky Home Checklist
If you already have a home with monolithic cladding these are the things you should look out for when doing routine maintenance:
Interior
- Black spotted mould on inside walls or ceilings (mould may also form on walls and ceilings because of internal moisture).
- Swollen architraves or MDF skirtings.
- Stained timber window or door trims.
- Stained carpet.
- A general feeling of dampness next to doors or below windows.
Exterior Cladding
Pay particular attention to corners and junctions in the cladding. Remember monolithic cladding relies on the paint coating to keep your home weathertight. Look for paint that has:
- Cracks.
- Worn areas.
- Surface bubbling.
- Ridging.
- Peeling.
- Any signs of lifting or de-lamination.
- Thin or transparent areas, particularly on exposed corners.
- Penetrations to walls
- Check around the meter box and any pipes penetrating the wall cladding to ensure they are flashed or sleeved.
- Decorative features must not penetrate the cladding and all fixings should be sealed.
- Check where fascias and gutters meet a wall surface. The paint finish should be continuous behind the end of the gutter and the roof junction should be flashed.
Roofing
- The roof should be checked for build up of debris that could track or hold water.
- Ensure all flashings are securely fixed and provide a secure overlap to the roofing, especially around penetrations from flues, vents and other services. If in doubt get the advice of a reliable roofing company.
- Check the clearance of claddings from the roof surfaces and flashings. It should be possible to easily run your hand under the cladding to enable the underside to be re- painted when needed.
- Ensure that there is a kick-out where a roof ends in a wall surface.
- Ensure that diverters are correctly fitted.
- Under or over windows
- Check for missing flashings, particularly head and sill flashings. If they are fitted they will be visible on the outside.
- Check the flashings to ensure they slope to the outside to spill water over the window or door-frame. Check at the ends to ensure they will not allow water to flow inwards at their ends.
- For curved windows check that the flashing has a stop-end to direct water to the exterior and not allow water to enter behind the wall cladding.
- Check the jambs to ensure they are sealed to the cladding.
- Check the corners of cladding on recessed windows - particularly check that there are no hairline cracks in the paint finish.
Solid Handrails
- Where the texture coating is carried over the balustrade leaks may not be visible. If you are unsure contact a building consultant for advice. The most reliable check is to measure the moisture content of the timber framing. This is best done using a moisture meter with probes through two small holes in an area that is not exposed.
- The timber floor structure should also be checked from the underside.
At Ground Level
- Check the clearance of the cladding from the ground. Options may be to lower a built- up garden area or provide paving that falls away from the house, but if this is not possible seek expert help.
- Check doorways and imagine how any flooding or puddles of rainwater might affect the doorway. Water does not need to flow through the doorway to cause problems, but may flow under the sill. It is possible that water might also enter through splashing. The ground may need to be re-contoured, or in the worst case, doors removed and raised.
Decks
- Ensure there is space between timber decks and cladding. It is important to regularly remove leaves and other debris caught up in the gaps.
- Waterproof decks should have no areas of lifting membrane. Joints should be tight and there should be no water ponding anywhere on the surface. The membrane should have a positive coving at all edges, including under doors. Check for nicks in the membrane.
- Paint-on membranes require regular checking and may become punctured even with a protective layer of tiles. Have these membranes checked annually and do not put off re-coating if the membrane is wearing.
- Make certain all drainage and overflows are clear. The overflow height should be at least 50mm below any floor area, and below any deck coving at walls or doorways. If you have any doubts, seek expert advice. Some decks have been constructed with untreated timber and may become dangerous if moisture has got into the framing.
If you suspect that your home has weather tightness problems, seek expert advice
Information supplied courtesy of Consumerbuild
